Works great installed on 2002 super duty, any ford with remote entry will accept these key pads,

Install is easy, programmed correctly the first time with a personalized code.

Works great installed on 2002 super duty, any ford with remote entry will accept these key pads,

I've come to believe that pretty much ANY Ford that has a factory installed keyless entry system is capable of using this product

Programming it with older Ford vehicles like mine (slightly different for newer vehicles) entailed turning the ignition on and off quickly 8 times (without starting vehicle), leaving ignition on and then using each of the existing remotes plus this new kp.

I used genuine Ford Motorcraft touch-up paint to paint the black bezel (it snaps off and on easily) to match my car for a very clean look.

Love this device I've only had it about a

I missed having the keypad on my latest F150 and this device looks stock and works great!

Love this device.

Excellent item works perfectly

Great item, but it comes with no instructions and no web site for instructions for how to mate it to the car

Excellent item works perfectly

Works great with the 2000 F350 super duty even though it is not listed as a product that fits

Put it on a 99 Super Duty and had to ask the ford garage about instructions

Works great installed on 2002 super duty, any ford with remote entry will accept these key pads,

Nice, compact and works s it should

great deal and fast shipping

Fast shipping& good buy

Installation and programming is easy, but you'll likely need YouTube instructions since the ones that came with the device are not great

Easy installation on my 2008 Ford Escape - works great!

Used this on my Ford E-150XLT, 2010 year - very easy enrollment and installation -

The wide range of vehicles that this covers is great until you realize that FoMoCo changed the pairing procedure several times during this time period.

The white cover, like the black cover is held in by several snap catches.

Works perfectly on Ford Transit passenger wagon (the truck not the car)This is a wireless keybad remote (there are no wires just a sticker in the back) that needs to be programed

I'd love to tell other 2012 Ford Focus owners what the procedure was for THAT model with the SYNC non-Nav system but given the amount of time I spent trying to FIND the procedure and all the nonworking suggestions I ran into along the way, I honestly don't remember what worked

wanted this for my 2012 mustang and hid it in the fuel door works great ; easy to program toi car

Leaving a positive review because the product seemed of good quality and worked

Stopped working after one month, ironic that's the right at the no return date!Very disappointing

I prefer the larger original keypad; however, in the scheme of life, this one is fine.

As you begin to pry on them with the small screwdriver, don't pry too much, just enough to release the keypad, the keypad will start to come out

Try to release as many tabs, top, bottom, and sides before prying the keypad out.

I used this on my 2002 F250 to replace my old keypad when the battery died.

I love this keypad, don't have to worry about getting locked out

This product worked as I expected, as the other reviews state, the one bad part, battery is not replaceable

Althoughyou will be told the battery is not replaceable, it actually is.

In the instructions for this unit, it explains that when battery gets to almost dead, the unit will cycle the lock when you open the door with key pad

Once the batteries are dead then the unit needs to be replaced

Supplies you will need: the battery, a thin, but stiff and strong metal blade - not sharp (I used a 1 1/2" metal putty knife (pk)), a heavy plastic putty knife with a tapered working edge, heavy duty double sided foam tape, small screw driver or key (for removing battery from its housing), adhesive remover and a rag.i) Remove the kp from its mounting position.

Supplies you will need: the battery, a thin, but stiff and strong metal blade - not sharp (I used a 1 1/2" metal putty knife (pk)), a heavy plastic putty knife with a tapered working edge, heavy duty double sided foam tape, small screw driver or key (for removing battery from its housing), adhesive remover and a rag.i) Remove the kp from its mounting position.

After removing most of the foam tape adhesive, I then alternated between using Goo Gone adhesive remover on a rag and the plastic putty knife until the adhesive was gone (this took 20 to 30 minutes)

To do this, I used a heavy gauge 2" plastic putty knife.