Be careful with thisi, it is shown at the bottom of the page for a microphone I ordered as "buy all three", well it was not made for a fat screw on condenser mic

It scrapes the arm and it wares the screw out, slowly grinding it down.

It seems somewhat strangely common that these desk mic booms come with a 3/8" screw connector like this one does.

The vice portion isn't very good, the screw itself being quite weak.

Looks great but the screw with ball that secures the arm broke off the first day, maybe this screw had a defect, that's the only reason i can give it a 4/5 :(

It's a thin table but the screw went completely into it without scratching or denting it up

Product was great for a year but after some time, the entire set stopped screwing in properly and couldn't hold up a Blue Snoball microphone without the microphone falling down and swaying side to side

AS a result, the screw is unusable and I just leave the stand sitting precariously in the base

The stand screw stripped and no longer worked within the first instillation

The screws come loose, and on top of that no matter how much I tighten and make sure it's all correct it shakes with something as simple as picking up my mouse and setting it back down and gives a little feedback

I got it because it works specifically with the Blue Snowball microphone, however, where the actual arm screws into the deck clamp is very flimsy and can't support the microphones weight, aluminum metal bent at just a little force over time.

Also the screw for the microphone clip has bad threads and almost ruined the clip that came with my $300 microphone

Doesn't support weight of my microphone, the screw latch at the bottom to secure onto the table is faulty.trash.

The screw on the clamp that holds the arm in place is very very bad

I got it because it works specifically with the Blue Snowball microphone, however, where the actual arm screws into the deck clamp is very flimsy and can't support the microphones weight, aluminum metal bent at just a little force over time.

Swinging the arm out of the way is a must, but the screw at the clamp makes it impossible to rotate easily

Very sturdy screws to hold it in place when you have made adjustments and just want it to stay still.

The screw to tighten stand to the desk broke off and won’t stay connect to the desk.

Does what it needs to do but buyers beware it does not come with the correct screw on adapter for the Blue Snowball.

Looks great but the screw with ball that secures the arm broke off the first day, maybe this screw had a defect, that's the only reason i can give it a 4/5 :(

You can't just put it on out of the box though, the screws are all really loose and you will want to get some crescent wrenches and screwdrivers and tighten everything up

it falls, quite often, it falls hard and has damaged my Microphone-cheap screw that doesn't allow you to swivel it without it moving on the deskConclusion: There are lots of better options out there, and because of the fact that it keeps falling off of my

All the screws were very loose, and the clamps don't tighten properly

It did not take long for the first tightening screw to come off and break

The screw for the mike insertion is always loose and the microphone drops.

Any screw in mic like Blue snowball works great

(see note 3)Just putting on an M4 female screw head like uxcell M4 Female Thread 33mm Plastic Star Head Screw On Clamping Knob 5pcs won't work so well because the elbow bolt is a carriage bolt, and the stem bolt is a plain hex bolt and unless you want to get out the sockets every time you adjust your mic, you would prefer a carriage bolt

Any screw in mic like Blue snowball works great

no luck (even the screws are junk)

The screw on the bottom came way too loose and would move freely about

Cheap plastic screws broke within hours

Biggest complaint is the screw that holds the thing still

Screw to keep the arm attached to grip it terribly thought out and flimsy

It has a useless screw to lock the the connector from your microphone to the actual stand but there isnt a hole for the screw so it just sits there doing nothing

no luck (even the screws are junk)

It was missing a screw to connect the extension to the table mount

The adjustable screw that was attached to my clamp was inserted incorrectly, and is unfortunately stuck in place

Within a few days they shipped me two new C-clamps with the correctly sized screw.

Buy it if u r broke

During a few recording sessions my keyboard clicks had interrupted an important e-sports play and it lost my friend his battle