-
I have to say, I was leery, at first, but with generous application of lubricant and going slow, I had a perfect 1" hole in very little time
-
This did the job for me, I was only making holes in fairly thick plastic, so I cannot vouch as it's usefulness for other materials
-
Fast, clean holes.
-
I have only used once but it brought up the .250 hole to the .750 hole size I needed with ease even though it was plastic it made for a nice clean hole
-
It partially drilled one hole in non hardened steel and then I wondered why I bought it in
-
This little beauty drilled four holes through 3/16" thick steel and looks as if it was still brand new and untouched!!
-
Versatile hole sizes
-
Got hole to correct size in less than 5 minutes
-
Tried to use this to drill a hole on the electric box, no luck
-
The metal box went as expected, when I tried to drill a clean hole in 1 piece of plastic the drill failed completely
-
Made the hole the perfect size.
-
My sink didn't have a big enough hole for the soap dispenser to
-
Worked well cutting holes in sheet metal to pass battery wires through
-
On thin material it makes wonderful clean holes...
-
The holes are really clean and smooth and I really have no complaints about this at all
-
Worked well cutting holes in 1/8” steel.1/4 the price of similar bits at Hime Depot.
-
Nice clean hole of 1 & 3/8"
-
Purchased to drill a few 1" holes in plastic, worked perfectly and was far cheaper than any other bit I found online or in the store.
-
Still made a smooth hole.
-
This bit drilled several accurate 1" holes in heavy guage stainless effortlessly with no wear so it was a good purchase
-
Drills crude holes
-
Worked fine for the first few steps of my first hole drilled but every hole after that was a real struggle.
-
It made the holes like a hot knife going into butter.
-
I bought this to punch one hole large enough to install a soap dispenser in the divider of my sister in law's stainless steel sink
-
saves time fitting dowels pipes for welding and other project needing shallow holes
-
Read some bad reviews but saw several good reviews so I purchased this to stole two 1/2” holes in a plastic beauty salon sink.
-
Tried to drill a hole , not even a scratch
-
If so then you know its near impossible to get a clean hole using a regular bit.
-
My sink didn't have a big enough hole for the soap dispenser to
-
Pretty easily cut a perfect hole into the deck of a stainless steel sink
-
I've done several holes in stainless steel and a couple in aluminum, and it works well
-
Leaves a nice clean hole.
-
Put a couple of Precise holes through A keg (stainless steel) without much guff
-
It created a perfect hole.
-
The hole is really easy to cut and very precise
-
Had to drill an 1-1/18" hole into four, 1/16" thick, aluminum plates First hole was fine
-
I tried to use this to drill a hole my stainless steal sink for a second faucet
-
Have drill 20+ holes in plastic and it worked great, right to the size I wanted...
-
Good clean hole.
-
Absolute garbage drilled 1 hole and couldn't finish it
-
Like putting a hole in butter
-
Good hole drill!
-
The first required a few clean holes in a metal box
-
This drill bit made a nice hole so that I can get to the switch.
-
I completed the job without problems--the holes were true and the bit did not warp the sheet metal.
-
Super heavy duty, does a good job putting holes in stainless pots.
-
i have used this several times to drill precise holes in the dash of my truck for fitting of switches, grommets etc and cuts very nicely.
-
I bought this to drill two holes in my stainless steel brew pot as recommended
-
Hole gets larger just like I figured.
-
Bought this to drill some holes in a burn barrel, works great
-
It left a smooth hole
-
Drilled one decent sized hole through mild stainless (very thin, very soft) before the coating came off and the cutting edges dulled
-
Super clean holes!