Other issue is that the clamp that attaches to your desk is limited to only a couple inches of

Also, the inner ring actually touches the outer ring, due to the lack of a proper clamping fitting mechanism.2.

After a couple weeks with this stand, the clamp has lost all of the sticky padding that comes on it to help it grip as well as has bent to be completely unusable.

the clamps on them are useless.

Clamp is pretty weak and bends if you tighten it to where you think it'll need to be

I clamped it to my desk, and within 30 second of holding my microphone, the clamp lost grip and everything fell to the ground

Cons:- The wobbly base and poorly designed clamp is a legitimate complain from other posters

I just prefer the other clamps that my other stand uses to secure itself on the table.

The clamp could be better/stronger, but it does the job.

The clamp for the desk is fairly good, though could probably use some more tackiness on one or both sides, maybe some rubber of some sort, but it holds on quite well

However mounting clamp is pretty weak and it can't handle even arm without microphone

The clamps don't hold very well and even with everything tightened down fully the stand itself still wobbles around on my desk

The clamp did not sadly

the clamp is good for about a week it starts to weaken and the stand its self is really weak

The clamps don't hold very well and even with everything tightened down fully the stand itself still wobbles around on my desk

Although I expected a somewhat heavier construction, the springs are strong and the clamp (the part that always breaks in my experience) is beefy enough for our heavy microphones.

The clamp set up isn't very wide opening, and wouldn't work where I had intended

However, the pop filter, the shock mount, and the clamp that is used to fasten the arm to a desk is poorly crafted and broke immediately upon setup

Do not go with this one, there is newer model with better mounting clamp, everything else is the same

The clamp on the pop filter instantly broke as many other reviews have noted

The clamp to attach the stand is a cheap thin metal disk that bends and doesn't support the stand

First the clamp was hard to set up, and second my microphone holder screw in bit was to big for the screw thing, but I made adjustments and it works now.

Very good arm stand, poor clamp design.

C clamp for mounting on the table is to weak and bends with just the weight of a NT1, shock mount and pop screen.

Package came destroyed, missing several peice, terrible quality clamp.

for anything over 3-4 pounds, you should at least look for a better base clamp.

The clamp was broken and wouldn't tighten

Upon further inspection I found the threads for the clamp were not secured, I was able to tighten the clamp after stabilizing the thread on the other side

Mounting clamp does not work very well.

The clamps are awful, they don’t tighten up all the way without messing up the the stand, and your microphone will continue to fall down 24/7

I broke the pop filter clamp three days after mounting it on my

The clamp is weak and won't stay connected to the table.2

The clamp for the pop filter is completely worthless

I may have just got a defective clamp though, the product pictures seem to show it as having a parallel top and bottom part of the clamp

Good Stand, but the clamp where it hooks up on the table is not the best.

Works wonderfully, only complaint was the clamp for the pop filter uses a plastic piece which broke when tightening it down.

I ordered a different, sturdier, clamp and all was well again

The clamp for the pop filter also looks deformed

Works wonderfully, only complaint was the clamp for the pop filter uses a plastic piece which broke when tightening it down.

While functional, the first time I mounted this to my table the clamp broke and the whole scissor assembly fell

And its missing the bottom clamp so i cant even set it up

clamp itself is good its a metal screw with a metal plate to hold it's self on the table or deskthe boom screw that holds the

Clamp to hold to table seems to work well as long as your table doesn't have a ridge of any sort along edge, but that doesn't matter because the stand struggles to hold itself up anyhow.

We rigged it so it still works, as long as we don't touch it