Although the clamp was designed for a thinner air vent size, I was able to get it to stay on the thick vents in my Nissan Rogue

I've used other air vent mounts in the past and hated them because they were always difficult to install/remove, but this mount is so much better

Being that it is in front of my air vent, it also keeps my phone cool

This is a great air vent holder

I've tried a few air vent mounts for my iPhone 6s and this is far and away the best that I have tried.

It's super easy to use as well — just slip the mount over one of your horizontal air vent slats, slap an adhesive metal plate onto the back of your phone (in my case, I opted to just put the plate in between my

The mount is pretty sturdy, doesn't fall and I like air vent mounts because sometimes I worry my phone might get too hot and putting it on a air vents cools the phone

I figured out that if I just position the phone in horizontal mode while making calls, the problem is solved because the microphone is no longer in front of the air vent

I've used other air vent mounts in the past and hated them because they were always difficult to install/remove, but this mount is so much better

This review will be heavily compared to the Wish House simply that's the only other air vent mount I have for comparison

Overall, it will depend on your air vents in your car if the mount will work properly, but it looks as if it would work for most cars

This mount fits right into the air vent in your car

the the swivel ball adds a little distance from the air vent, allowing me to still access the buttons on the center console, which I had a hard time accessing with my old phone mount

Overall, it will depend on your air vents in your car if the mount will work properly, but it looks as if it would work for most cars

You just slide it onto the air vent blades and you are done

This mount fits right into the air vent in your car

It's super easy to use as well — just slip the mount over one of your horizontal air vent slats, slap an adhesive metal plate onto the back of your phone (in my case, I opted to just put the plate in between my

If you like to mount your phone on your air vents, this is the perfect mount

I do wish that the adjustment ring didn't loosen so easily, and I wish it didn't block so much of my air vent (especially in summer!), but these are just quibbles.

In contrast, the air vent mount from WizGear went onto my air vent *

This is a great air vent holder

The set up is smart, as they provide an adhesive magnet that attaches to your phone or case, then sticks to the powerful magnet which you place on your air vents

(Toyota Rav4 with black interior), 3) falls off the air vent easily (probably because the rubber legs don't have enough give to stay open

Attaches firmly to the air vent

The set up is smart, as they provide an adhesive magnet that attaches to your phone or case, then sticks to the powerful magnet which you place on your air vents

It slides easily onto the air vents and stays in place very well

In addition, this car mount will be compatible with most cars because it can attach to two different size air vent blades

My usage is in a 2009 Mazda with horizontal air vents

I like that it is extended out which allows you to move it past the air vent knob which, depending on what car I'm driving can be a real pain next to my phone.

There are basically 2 types of air vent mounts

CONSThe car mount's rubber legs are 1) spaced too closely together (requiring significant force to push the mount onto the air vent), 2) too hard, scratching the paint off of my air

They work as they should

Good as that means it should grip the vents better, but bad if you're looking to take the mount off on a frequent basis as this may wear down the clips or scratch your vents should the clips wear down.-Ball joint is also a double edge sword

Great product, works exactly as you'd expect and hope.

These connect snugly and are just the right length for my multi-device charging station as well as for my laptop

Very good t you

n’t break the wires on the inside